PremiumCoat System

Premiumcoat ImagePremiumCoat sustainable roofing and waterproofing system is one of the highest quality roofing and waterproofing systems available. It is recognized by Factory Mutual as a Class 1 roofing system as both a stand alone roof system and as a recover system over a variety of substrates. It is made of only the best raw materials to form a flexible, U. V. resistant elastomeric compound and is fully reinforced with a tough nonwoven polyester fabric which has been designed for roofing and flashing applications of all types.

 

PremiumCoat is easy to apply, safe to work with, and requires no special equipment. Properly installed, the system includes a 10-year warranty in specific roofing applications, which can be extended every 10 years under a proper maintenance schedule.


PremiumCoat

Uses:

  • Metal roof waterproofing and cooling
  • Parapet wall waterproofing
  • Flat and low-pitched roof waterproofing
  • Flashing of all types
  • Concrete waterproofing
  • Plywood waterproofing
  • Deck waterproofing
  • Exterior wall waterproofing

Advantages & Benefits:

  • Factory Mutual and Dade County approved.
  • Sustainable roofing system that saves expensive removal and disposal cost.
  • Ultraviolet and Infrared resistant for added durability.
  • Combination of High Albedo & Emissivity reduces heat and lowers energy costs.
  • Resistant to acid rain and chemical pollutants to protect roof or wall from fallout damage.
  • Won’t spread flame over non-combustible surfaces.
  • Excellent adhesion holds substrate in place even in hurricane force winds.
  • Wide range of colors provides beautiful architectural finish.
  • Meets V.O.C. emissions regulations to eliminate facility downtime during application.
  • Non-toxic formulation is safe to install.
  • Easy application and cleanup.
  • No special equipment required to install.
  • 10-year extendable warranty available.
  • PremiumCoat has been approved by Factory Mutual (FM) as a class 1 roof system for application over insulation board, new built up roofs, existing built-up roofs, metal roofs (including historic) and concrete.

Standard Colors:

PremiumCoat Colors

Application Specifics:

Surface Preparation: Priming
 
Wood Surfaces
 No priming necessary on unpainted wood or plywood.
Concrete & Masonry Surfaces
 Must be primed with a coat of BarrierGuard waterproofing sealer. Dry time-2 hours.
Metal
 No priming necessary on previously protected or weathered galvanized metal. Unprotected iron and steel must be primed with StableRust Primer. Dry time-2 hours.
Painted Surfaces
 SureBond primer must be applied over any areas that exhibit chalking.
EPDM
 Clean and Prime EPDM by applying CleanAct Primer to the surface at a coverage rate of 250 sq/ft/gal. Rinse roof thoroughly twice.
PVC, TPO, HYPALON
 Apply SureBond primer by brush, roller or spray. Coverage rate approximately 125-250 sq/ft/gal
Insulation Board, Roll Roofing, Modified Bitumen, Smooth Built-Up
 No priming necessary.
NOTE: All existing roof surfaces should be power washed and cleaned to remove any
loose or flaking particles, lubricants or excess dirt or dust.
Surface Preparation: Application
  • Install cant strips at internal corners, and flat metal drip edge on outside perimeter.
  • Apply 6 inch wide strip of FoundationCoat, fabric, and saturation coat over cracks and non-working joints.
  • Apply 12 inch wide strip of FoundationCoat, fabric, and saturation coat over all cant strips and around the entire perimeter of the roof.
  • Apply FoundationCoat and saturation coats at a total rate of 40 sq. ft/gal minimum.
  • Apply FoundationCoat to the entire area.
  • Embed fabric directly into the coating while still wet.
  • Overlap adjacent runs of fabric 4 inches minimum (per side).
  • Immediately follow with a saturation coat to cover fabric and allow to dry.
  • Using 6, 8, 12, or 40 inch flashing fabric, continue waterproofing material up vertical surface and onto roof deck, over insulation board and on to the drip edge.
  • Apply 2 coats of FinishCoat at a combined total coverage rate of 70 sq. ft/gal.
  • Flash all penetrations through waterproofing with complete fabric system.
  • Apply waterproofing material to minimum 40 mil total cured thickness.
 

Clean Up:

Thoroughly rinse application equipment with clean water.

Safety & Handling:

For specific information regarding safe handling of this material please refer to the Material Safety Data Sheet (MSDS).

Storage & Shelf Life:

PremiumCoat has a shelf life of eighteen (18) months provided it is stored in tightly closed containers, protected from sunlight and stored at temperatures between 40º F and 90º F.

Technical Data:

Product
 Reinforced Acrylic Elastomeric
Shelf Life and Storage Conditions
 18 months if unopened and stored between 40º F & 90º F
Density
12.1 lb/gal
Application Temperature
 Min + 40º to 105º F (Ambient), min + 36º to 130º F (Surface)
Drying Time
Touch dry:1 - 4 hours at 77º F and 40% humidity, Full cure: 7 days
Total thickness
 40-45 mils
Elongation of cured system
 53% fabric reinforced system (ASTM D-412)
Tensile strength of cured system
2210 psi (ASTM D-412)
Water vapor permeability
3-5 perms (ASTM D-1653)
Fungus Resistance
No growth supported (ASTM G-21)
Algae Resistance
No growth supported (ASTM G-29)
Flammability
Class A (ASTM E-108)
Salt spray test
No effects noted (ASTM B-117)
Percent solids
66.9%
Low temperature flexibility
180º flexibility; bend at -15º
 
Substrates
Uplift Pressure Resistance
Wind uplift protocol
(PA-114)
Concrete
6,098 psf
 
Plywood
600 psf
Uplift pressure resistance
Polyisocyanurate
1,189 psf
 
Smooth Surface BUR
2,261 psf
 
Granule Surface Cap Sheet
1,753 psf
Accelerated weathering (ASTM G-26)
Meets Dade County protocol for 3,600 hrs.
  

 

Technical Drawings:

Hydro-Stop, Inc.
1465 Pipefitter Street • Charleston, SC 29405
(800) 739-5566 • (843) 745-9600


Approvals

"Hydro-Stop," all Hydro-Stop logos, BarrierGuard, ClearGuard Plus
and PremiumCoat are registered trademarks of Hydro-Stop Inc, Copyright 2003